Eazi Grip


Eazi-Guard™ Stone Chip Protection

For Race and Track bikes; stone chips, abrasions, stress fractures and scratches can quickly damage fairings, forks and bodywork. For Road bikes, the harmful effects of road salt, tar and airborne particles can dramatically reduce the resale value of your bike.

Eazi-Guard™ stone chip protection film is a Non-Yellowing, Ultra-Thin, Ultra-Tough, polyurethane protection film, designed to protect your bike and virtually eliminate damage. The unique properties of our Protection film enable it to disperse the impact energy of gravel and small stones, bouncing them off and leaving your bodywork untouched beneath.

Eazi-Guard™  Stone Chip Protection Kits are easy to fit, with sectional pieces, that in conjunction with our advanced fitting solution, simply float into place. Eazi-Guard™ Kits are extremely conformable around even tight radii and compound curves, making them Eazi to fit at home. Standard kits cover the tip of the front mudguard, front fork shields, nose cone, leading edges of the fairings and tail unit. For customers requiring more than just the ‘standard’ coverage, for example paniers, top boxes, wing mirrors, headlights or any other requirements, we have an in-house design team that can produce bespoke patterns.

Together with our standard range of pre-cut kits, we also offer rolls in 75mm, 100mm & 150mm widths , ideal for protecting front forks, chassis rails and swingarms. Eazi-Guard is an essential addition for every toolbox.

Purchase Eazi-Guard

In addition to our Eazi-Guard™ Stone Chip Protection, we have the ALL NEW Eazi-Grip™ Dashboard Protectors!

Offering Anti-Scratch properties, our Dashboard Protectors provide excellent screen coverage with an exceptionally simple installation process.

Purchase Dashboard Protector

Application Video


Eazi-Grip™ supported teams and riders have had huge success at the 2019 IOM TT with 5 race wins, 13 podiums and over 35 top ten finishes throughout the week of races! Supported riders took the top step of the podium in the PokerStars Senior TT, RL360 Superstock TT, Monster Energy Supersport Race 1 and 2 and the RST Superbike Race. All our products supplied to the leading race teams around the world are available to purchase from our website.

Eazi-Guard™ Application Guide

Careful preparation and application will ensure maximum performance in all environments and will ensure 100% satisfaction with your purchase.

  • 1Clean the surface...

    Clean the surface of the application area with the enclosed isopropyl wipe or degreaser, do not use products such as methylated spirits, lighter fuel or white spirits as these leave behind a greasy residue that will affect the ability of the adhesive to bond to the surface to be protected.

  • 2Use the enclosed...

    Use the enclosed diagram to identify the parts to be fitted.

  • 3Fill the spray bottle...

    Fill the spray bottle with warm water to the top of the label, the spray bottle contains a small amount of concentrated lubricant that when mixed with water will produce a fitting solution. Spray your fingers with the fitting solution.  Avoid touching the adhesive when dry, as this will leave a fingerprint in the film, wetting your fingers will help to avoid fingerprints.  Carefully remove the film from the backing liner spraying both sides of the film.  This will prevent static from attracting any contamination and will significantly ease positioning of the film allowing it to float into position.  Once the surface has been cleaned and all contaminate removed, spray the fitting solution onto the area of paintwork to be protected.

  • 4Locate and position the film...

    Locate and position the film on the application area.  Manoeuvre the film slightly to release any surface tension.  If the film does not slide easily, remove the film and spray more solution on both the film and application area.  When the placement is correct squeegee to expel the solution out.  Work from the centre of the film out towards the edge using short smooth strokes to expel all of the air and liquid securing the film into place.  Remember to take your time and work on section at a time to prevent creases.  If the film needs to be repositioned during the application and it has not dried lift the film and respray both sides of the film and the surface before reapplying.  If any creases or bubbles appear, slowly and gently work out towards an edge using a squeegee or your fingers.  If the film has not dried, the film can be lifted just pas the bubble and reapplied.  To remove any contaminates on the film, simply spray with fitting solution prior to application and gently wipe away any debris with your finger.

  • 5Dry off any excess...

    Dry off any excess solution with a dry cloth.  If any edges lift during the drying process, use your finger to press and hold down for 30 seconds to activate the pressure sensitive adhesive.  Allow the Eazi-Guard™ film to set for a few hours to complete the curing process and to ensure a strong and long lasting bond.

Purchase Eazi-Guard 


For all customers who require a customized fitting service, please contact our friendly sales team on 01772 459931.


Application Video

Disclaimer: Motorsports are dangerous activities and could cause injury or death. Eazi-Grip™ / Eazi-Guard™ assumes no responsibility for damage or injury caused by this product. It is the responsibility of the user to determine both the suitability of the product and the correct application.
Please note that Eazi-Grip tank grips work on the principle of creating extra friction between the rider and tank and a degree of wear should be expected to both the riders leathers and the tank grips. Accordingly the company accepts no liability whatsoever for any incidental damage caused to motorcycle leathers and/or other clothing worn by the rider as a result of the use of the product as by its very nature the grip is dependent on friction between the rider and the cycle.

© 2020 Eazi-Grip   All Rights Reserved

Website Designed & Built by Stone Create